Dataset: GN01 Dissolved Ba Cd Cu Ga Mn Ni and V
Deployment: HLY1502

Clean seawater samples were collected using a GEOTRACES CTD referred to as GT-C/12L GoFlo. For more information, see the cruise report. Additional near surface samples were collected using either a small boat or through the ice using Teflon coated Tygon tubing and a trace metal clean pump (IWAKI, model WMD-30LFY-115).

Water samples were filtered through pre-cleaned, 0.2 µm Pall Acropak Supor filter capsules as described elsewhere (e.g., Cutter et al., 2012; Hatta et al., 2015). Filtered water was collected in 125 mL HDPE bottles (Nalgene) that had been precleaned by soaking in hot 1.2 M HCl (reagent grade) for at least 8 h with subsequent thorough rinsing with ultrapure distilled deionized water (Barnstead E-pure). Small boat and under-ice samples were first collected into large acid-washed carboys and subsampled into 125 mL bottles.

Dissolved Ga was determined by isotope dilution ICP-MS using a ThermoFisher Element 2 operated in low resolution. Samples were concentrated using Mg(OH)₂ co-precipitation (e.g., Shiller & Bairamadgi, 2006; Zurbrick et al., 2012). Briefly, in this technique, a small addition (~70 µL) of clean aqueous ammonia is added to the acidified seawater sample (~7.5 mL) which precipitates a fraction of the dissolved magnesium as the hydroxide, which in turn, scavenges the gallium from solution. An enriched isotope spike of known concentration was prepared using purified enriched ⁷¹Ga (99.8%), obtained from Oak Ridge National Laboratories.

Because there is a significant interference of doubly charged ¹³⁸Ba with ⁶⁹Ga, the precipitate was washed three times with a solution of high purity 0.1% NH₄OH to minimize residual Ba. The precipitate was then dissolved in 550 mL ultrapure 3% HNO3 (Seastar Chemicals, Baseline) and analyzed in low resolution using a ThermoFinnigan Element 2 High Resolution Inductively Coupled Plasma Mass Spectrometer (HR-ICP-MS). Isotopes monitored on the ICP-MS were ⁶⁹Ga, ⁷¹Ga, and ¹³⁸Ba. A slight correction for residual Ba was made based on the ratio of responses at masses 69 and 138 to a Ba standard solution. Because the residual salt content varied from sample to sample, it was not possible to matrix-match the Ba correction standard. However, typically, this correction affected the final result by < 2.5 pmol/kg; where higher Ba corrections were noted, the sample was reprecipitated and re-analyzed because of concerns about the accuracy of applying the Ba standard correction to samples of high salt content.

The reagent blank contribution to the dissolved Ga analysis is typically 0.6 pmol/kg and the detection limit (based on 3 times the standard deviation of the blank) is 0.3 pmol/kg. Repeated runs of US GEOTRACES intercalibration samples (GS and GD), in-house reference solutions, and cast overlap samples suggest a precision of ± 4%; the limit of detection for Ga was 1.5 pmol/kg. Recovery of the method, as determined by repeated analysis of a spiked and unspiked seawater sample was 100 ± 7%.

Dissolved Ba was measured using a ThermoFisher Element 2 Inductively Coupled Plasma Mass Spectrometer (ICP-MS) and the isotope dilution method as described by Jacquet et al. (2005). Aliquots (50 μL) of each sample were spiked with 25 μL of a ¹³⁵Ba-enriched solution (~170 nM) and then diluted 30-fold with 0.2 μm ultrapure filtered water. A sample of ~93% enriched ¹³⁵Ba was obtained from Oak Ridge National Laboratories for use as the enriched isotope spike. The ICP-MS was operated in low resolution and both ¹³⁵Ba and ¹³⁸Ba were determined. The samples were bracketed every 10 samples with a blank and the spike ¹³⁵Ba solution. The volumes of the spikes, samples and dilution water were accurately assessed by calibrating each pipette by weight. The reproducibility error of this method was estimated by comparing samples collected at the same depths on different casts at the same station. For 12 pairs of these replicate samples, the average absolute deviation of 0.7 nmol/kg or typically 1.5%. Repeated runs of runs of US GEOTRACES intercalibration samples and in-house reference solutions suggest a similar precision; the limit of detection for barium was 0.7 nmol/kg. Our precision is similar to that reported by other labs for Ba (e.g., Jacquet et al., 2005).

Dissolved δ138Ba (Ba isotopes) were measured at WHOI (Woods Hole Oceanographic Institution) using a ThermoFinnigan Neptune multicollector ICP-MS. Five mL aliquots were prepared by first spiking with a known quantity of 135Ba–136Ba double spike to achieve a spike:sample ratio of between 1-2. Following equilibration with the spike, samples were co-precipitated with CaCO₃ by dropwise addition of 350 μL of 1 M Na₂CO₃ solution. The precipitate was dissolved and reconstituted in 2 M HCl for ion-exchange chromatography. Chromatography protocols are detailed in Horner et al. (2015). Following purification, samples were again reconstituted in 2 % nitric acid and analyzed for δ138Ba at the WHOI Plasma Facility. Samples were aspirated at 140 μL/min, desolvated using an Aridus II, and introduced into the instrument using 1 L/min Ar carrier gas containing 2-5 mL/min admixed nitrogen. Samples are measured in low-resolution mode relative to concentration- and spike:sample-matched aliquots of NIST SRM 3108 (≡0 ‰), measured after every fourth sample. Samples are themselves analyzed between 2-4 times, and Ba-isotopic compositions calculated using an iterative, geometric-based deconvolution of spike-sample mixtures.

Dissolved V, Ni, Cu, Cd, and Mn were determined using 14 mL of sample that was spiked with a mixture of isotopically-enriched Ni-62, Cu-65, Cd-111, and V-50 (Oak Ridge Nat’l. Labs). Each spike was >90% enriched in the listed isotopes, except for V-50 (0.25% natural abundance) which was 44.3% enriched. The sample/spike ratio was chosen so as to have the analytical isotope ratios approximately the geometric mean of the natural and enriched spike isotope ratios. Samples were then extracted/pre-concentrated using a SeaFAST system (Elemental Scientific, Inc.) operated in offline mode. A 10-mL sample loop was employed and the elution volume was 750 µL. A similar online SeaFAST extraction procedure is described by Hathorne et al. (2012) for rare earth elements. The extracted samples were subsequently analyzed using a Thermo-Fisher high resolution ICP-MS with an Apex-FAST high efficiency sample introduction system with Spiro desolvator (Elemental Scientific, Inc.). All elements were determined in medium resolution, except Cd which was determined in low resolution. For Mn-55 the V, Ni, and Cu spikes served as internal standards. Calibration was checked by analysis of a large-volume composite North Atlantic surface seawater sample. Spiked (with a natural isotopic abundance elemental spike) and unspiked aliquots of this sample were analyzed twice in each analytical run. Ti-47 and Cr-52 were monitored to correct for any Ti-50 or Cr-50 isobaric interference on V-50; the correction was generally <1%. Likewise, Mo-98 was monitored to correct for MoO⁺ interference on Cd isotopes.

The reproducibility error of this method was estimated by comparing samples collected at the same depths on different casts at the same station as well as by repeated measurement of GEOTRACES reference waters and an in-house standard. Recovery of the method was determined by repeated analysis of a spiked and unspiked seawater. The recoveries, precisions, and comparisons to reference waters are shown in Table 1 (see Supplemental Files).