Cruises and sample collection

Water samples were collected as part of the SoMMoS project during twelve cruises, from February 2018 until January 2019. Each cruise took samples at two THEMO (Texas-Haifa Eastern Mediterranean Observatory) stations.

THEMO2, an open ocean station at a depth of ~1500 m (~50 Km from the coast, 32.820 N, 34.380 E), and THEMO1 which is positioned at the edge of the continental shelf at ~125m depth (~10 Km from the coast, 33.040 N, 34.950 E). THEMO2 was sampled from 12:00-22:00 (local time), while THEMO1 was sampled during the night, typically 00:00-02:00 (local time). Here, we will present information from data collected at the offshore THEMO2 station.

Start and end data of the cruises and sampling research vessel (no specific cruise IDs):

07/02/2018      08/02/2018: R/V Bat-Galim
05/03/2018      06/03/2018: R/V Mediterranean Explorer
09/04/2018      10/04/2018: R/V Mediterranean Explorer
14/05/2018      15/05/2018: R/V Bat-Galim
18/06/2018      19/06/2018: R/V Mediterranean Explorer
09/07/2018      10/07/2018: R/V Mediterranean Explorer
06/08/2018      07/08/2018: R/V Bat-Galim
05/09/2018      06/09/2018: R/V Mediterranean Explorer
08/10/2018      09/10/2018: R/V Mediterranean Explorer
05/11/2018      06/11/2018: R/V Bat-Galim
03/12/2018      04/12/2018: R/V Mediterranean Explorer
21/01/2019      22/01/2019: R/V Mediterranean Explorer

Samples were collected using a 12-bottle rosette with 8 L Niskin bottles. Samples were collected at 20-24 depths across the entire water column (11-12 bottles between the surface and 200 m, which we define here as the photic zone). Sampling depths were selected based on real-time data of Conductivity, Temperature, Depth (CTD) profiler (Seabird 19 Plus) from the down-cast before each sample collection in the up-cast, an oxygen optode (on some cruises) and a fluorescence meter (Turner designs, Cyclops-7). The continuous data was processed using the Sea-Bird data conversion software, and minimized using bin averaging. One bin of data lines was defined as a change of 1 decibar (db) between each bin. The first two meters of measurements were compiled together to account for sensors and CTD pump adjustment time and rosette depth while at sea surface.

Nutrients

Nutrient samples were collected in acid-washed 500 ml plastic containers and immediately filtered through 0.22 μm Nalgene rapid-flow filter units. The first two filtrates were discarded, and the final sub- samples collected in new 50 ml falcon tubes and stored in the dark at 4 ◦C in racks. The samples were transported to the analytical lab at the marine station at Sdot-Yam within 12–15 h of sampling and dissolved nutrients determined using a SEAL AA-3 autoanalyzer system (SEAL, 2011). To minimize crosscontamination in the laboratory, ammonium was analyzed first alone using an automated ophthalaldehyde (OPA) fluorescence method. Samples were placed in the sample trays and only opened immediately before the sample probe took the sample. The baseline water used for ammonium determination was freshly prepared Milli-Q (MQ) water. The next parameters to be determined were dissolved nitrate and silicate. The methods used were Cd reduction and diazo dye for nitrate & nitrite (hereafter referred to as Nox), and molybdate blue in the presence of oxalic acid for Silicate. The baseline water used for these determinations was also MQ water. For the August cruise nitrite was also determined by carrying out a run also using coloured diazo dye but without Cd reduction. Finally, a 3rd run was carried out using an ultra-low level phosphate (DIP) method involving using a 100 cm long flow cell (LWCC) and molybdate blue determination derived from Murphy and Riley (1962). The blank used for phosphate determination was surface seawater, whose DIP value was determined in a previous experiment in which we determined a refractive index correction by removing the ascorbic acid reagent. It was not possible to use MQ as the baseline, as has been used elsewhere because the MQ water in our lab (derived from desalinated water) contains ~20 nM DIP.

40 ml subsamples for Total Dissolved Phosphorus (TDP) were taken from the filtered samples on-board, acidified with 0.2 ml of 2M sulfuric acid and frozen immediately in racks. The samples were transported to the laboratory at the Sdot Yam marine station and stored at −4 ◦C until later analysis. After thawing the samples, 4 ml of acidified potassium persulphate was added to each sample in a glass autoclavable bottle. The closed bottles were autoclaved for at least 30 min and allowed to cool overnight. The samples were then transferred to 50 ml Falcon tubes and analyzed using the same procedure as described for DIP. In order to determine the reagent blank, a similar procedure was used substituting MQ (and 50 nM and 100 nM phosphate) for the sample, adding 4 ml of acidified potassium persulphate into glass autoclave bottles. The reagent blank was treated the same way as the seawater samples.

Bacterial and primary productivity

Heterotrophic prokaryotic productivity (hereafter referred to as bacterial productivity, BP) was estimated using the 3H-leucine incorporation method (Simon and Azam, 1989; Smith and Azam, 1992). Triplicate 1.7 ml of ocean water were taken from each sampled depth and incubated with a 7:1 mixture of ‘cold’ leucine and ‘hot’ 3H-leucine, respectively (final concentration 100 nmol leucine L-1) for 4 h at room temperature in the dark immediately after sampling. Preliminary experiments show that this was the saturating level of leucine in the offshore water of the SE Mediterranean Sea. After incubation, incorporation was terminated by adding 100 μl trichloroacetic acid (TCA). As a negative control for non-specific binding, another set of triplicates were sampled from a surface layer and treated with TCA immediately after the addition of the radioactive tracer. At the end of each cruise, the samples were processes using the micro-centrifugation protocol and 1ml scintillation cocktail (ULTIMA-GOLD) was added to all samples before counted using TRI-CARB 2100 TR (PACKARD) scintillation counter. A conversion factor of 3 kg C per mole of leucine incorporated and an isotopic dilution of 2.0 were used to calculate the C incorporated (Simon and Azam, 1989).

Net daily photosynthetic carbon fixation rates were estimated using the 14C incorporation method (Nielsen, 1952), with several modifications (Hazan et al., 2018). Triplicate 50 ml samples were taken from each depth within the photic zone and from one aphotic depth using sterile vials and kept at surface light and temperature conditions. The ‘dark’ sample served as blank and was kept under the same temperature as the ‘light’ samples. Radioactive spiking was done at ~08:00 AM the day following of the cruise in order to start a 24h incubation for all samples (including those collected at THEMO-1 station, not shown) at the same time. Early work by Letelier and colleagues (1996) at station HOT showed that prolonged on-deck incubations, similarly to the protocol used in this study, may result in underestimated PP rates as it cannot precisely mimic the temperature and illumination levels in-situ. Our preliminary tests concur with this conclusion and found that ashore incubations underestimate PP rates by up to ~20% compared to incubations onto a mooring rope tied to the ship (Figure S2). Samples were spiked with 50μl (5 μCi) of NaH14CO3 tracer and were incubated for 24 h under 3 light regimes: surface illumination (samples from the upper mixing depths), 50% illumination (samples from below the mixing depth to the DCM) and ~1% illumination (samples from the DCM and below). Shading was performed using neutral density nets, thus changing light intensity but not spectral properties. Water samples were then filtered through GF/F filters (0.7 μm nominal pore size, 25 mm diameter) using low vacuum pressure (< 50 mmHg) and rinsed 3 times with filtered sea water. Filters from each sample were then put in scintillation vials where 50 μl of 32%HCl solution was immediately added in order to remove excess 14C-bicarbonate and kept overnight for incubation. After incubation 5 mL scintillation cocktail (ULTIMA-GOLD) was added to the samples and counted using TRI-CARB 2100 TR (PACKARD) scintillation counter. Three random aliquots were counted immediately after the addition of the radiotracer (without incubation) with ethanolamine to serve as added activity measurements.

Picophytoplankton abundance using flow-cytometry

Triplicates water samples (1.5 ml) were collected from each sampling depth, put in cryo-vials (Nunc), and supplemented with 7.5 µl 25% glutaraldehyde (Sigma). Vials were incubated in the dark for 10 min, flash-frozen in liquid nitrogen, and stored in -80 oC freezer. Before analysis, samples were thawed in the dark at room temperature. Each sample was run twice on a BD Canto II flow-cytometer with 2 μm diameter fluorescent beads (Polysciences, Warminster, PA, USA) as a size and fluorescence standard. In the first run three types of phytoplankton cells were identified based on their natural auto-fluorescence: Prochlorococcus, Synechococcus and picoeukaryotes. Cells were differentiated based on cell chlorophyll (Ex482nm/Em676nm, PerCP channel) and phycoerythrin fluorescence (Ex564nm/Em574nm), and by the size of cell (forward scatter). Before the second FCM, run samples were stained with SYBR Green I (Molecular Probes/ ThermoFisher) to enable counting followed by detection at Ex494nm/Em520nm (FITC channel). This provided counts of the total bacterial population (phytoplankton + heterotrophic bacteria and archaea) as well as a distinction between cells with High or Low DNA content (not shown). Data were processed using FlowJo software. Flow rates were determined several times during each running session by weighing tubes with double-distilled water, and counts of the standard beads were used to verify a consistent flow rate.

Algal pigment markers

Eight litters of seawater were collected from all photic sample depths and one from a dark depth (depth varies between cruises). Water was filtered onto GF/F filters (0.7 μm nominal pore size, 47mm diameter, Waters) using a peristaltic pump until either all 8 L were filtered or the filter became blocked, in which case the volume filtered was recorded. Filters were placed in cryo-vials and flash frozen in liquid nitrogen until they could be stored in a -80 oC freezer. Pigments were extracted in 1ml 100% methanol for 3 h at room temperature and clarified using syringe filters (Acrodisc CR, 13 mm, 0.2 μm PTFE membranes, Pall Life Sciences). Total chlorophyll was measured spectrophotometrically using a NanoDrop 2000c (Thermo Sciences) at 632, 652, 665 and 695 nm, and the concentration of chlorophyll a was calculated (Ritchie 2008). Ultra high-pressure Liquid Chromatography (UPLC) was performed on an ACQUITY UPLC system (Waters) equipped with a photodiode array detector. A C8 column (1.7 μm particle size, 2.1 mm internal diameter, 50 mm column length, ACQUITY UPLC BEH, 186002877) was used. The chromatography method was adapted for UPLC from the LOV method (Hooker et al., 2005). Samples were preheated to 30 °C and column to 50 °C before each run. Running buffers were a 70:30 mixture of methanol and 0.5M ammonium acetate (buffer A) and 100% methanol (buffer B). The program consisted of an isocratic run using a 80:20 mixture of buffers A:B for 2min, followed by a linear gradient to 50:50 for 7 minutes and an increase to 100% solvent B. The flow rate was 0.5ml/min. Pigment standards from DHI (Denmark) were used to identify the UPLC peaks (chlorophyll a, divinyl-chlorophyll a, chlorophyll b, zeaxanthin, diatoxanthin, fucoxanthin, peridinin, 19’- butanoyloxyfucoxanthin and 19’- hexanoyloxyfucoxanthin). Due to potential degradation of the pigment standards, we present the total chlorophyll measured spectrophotometrically and the pigment ratios within each UPLC run.

sommos.csv